Lapping/uk: Difference between revisions

Latest revision as of 17:03, 17 March 2025

Залежно від типу моторизованого транспортного засобу існує два способи контролю тиску в гальмівній трубці: прямодіючий, непрямодіючий.

Self-Lapping

У прямодіючих системах тиск у гальмівних магістралях регулюється автоматично. Машиніст може встановити ручку крану машиніста в будь-яке положення в діапазоні. Чим далі він встановлений у напрямку «від себе», тим сильніше гальмівне зусилля, і навпаки. Залежно від положення ручки, клапан автоматично регулює тиск в гальмівній магістралі.

Non-Self-Lapping

The non-self-lapping control valves are older. With them, the control lever manipulates the brake pipe pressure directly, and the process is more hands-on. The lever has a few fixed positions. Two of the positions, called “release” and “service” can be thought of as adding and releasing the brake pipe pressure, respectively. The position in-between them, called “lap”, is used to maintain whatever pressure is in the brake pipe. The furthest position, called “emergency”, releases pressure at the fastest possible rate.

By controlling the brake pipe pressure, you indirectly control the cylinder pressure, and thus, brake application.

Auxiliary reservoirs are partially drained whenever brakes are applied. When brakes are then released, it takes some time for the reservoirs to be recharged. The lap position, however, functions only if the auxiliary reservoirs are full. So, to stay in full control over non-self-lapping brakes it is recommended to not release when knowing that moments later braking may be needed again. Calculated, infrequent moves are advised instead.

Monitoring

With both control valve types it is crucial to monitor the brake pipe and cylinder gauges to fully understand the current brake state.

Conflicts

In case a train contains multiple motorized vehicles their control valves are in conflict. The conflict can be even more severe if there are mixed self-lapping and non-self-lapping valves in the train. To ensure safe operation it is necessary to cutout all excess control valves, other than the one intended to be used.

@@ Line 1: / Line 1: @@
 <languages />
+<div class="mw-translate-fuzzy">
 Залежно від типу моторизованого транспортного засобу існує два способи контролю тиску в гальмівній трубці: прямодіючий, непрямодіючий.
+</div>
+<div lang="en" dir="ltr" class="mw-content-ltr">
+==== Self-Lapping ====
+</div>
+<div class="mw-translate-fuzzy">
 У прямодіючих системах тиск у гальмівних магістралях регулюється автоматично. Машиніст може встановити ручку крану машиніста в будь-яке положення в діапазоні. Чим далі він встановлений у напрямку «від себе», тим сильніше гальмівне зусилля, і навпаки. Залежно від положення ручки, клапан автоматично регулює тиск в гальмівній магістралі.
+</div>
+<div lang="en" dir="ltr" class="mw-content-ltr">
+==== Non-Self-Lapping ====
+</div>
+<div lang="en" dir="ltr" class="mw-content-ltr">
+The non-self-lapping control valves are older. With them, the control lever manipulates the brake pipe pressure directly, and the process is more hands-on. The lever has a few fixed positions. Two of the positions, called “release” and “service” can be thought of as adding and releasing the brake pipe pressure, respectively. The position in-between them, called “lap”, is used to maintain whatever pressure is in the brake pipe. The furthest position, called “emergency”, releases pressure at the fastest possible rate.
+</div>
+<div lang="en" dir="ltr" class="mw-content-ltr">
+By controlling the brake pipe pressure, you indirectly control the cylinder pressure, and thus, brake application.
+</div>
 <div lang="en" dir="ltr" class="mw-content-ltr">
-On non-self-lapping systems, the process is more hands-on. The lever has a few fixed positions. Two of the positions, called “release” and “service” can be thought of as adding and releasing the brake pipe pressure, respectively. The position in between them, called “lap”, is used to maintain whatever pressure is in the brake pipe. The furthest position, called “emergency”, will release pressure at the fastest possible rate.
+Auxiliary reservoirs are partially drained whenever brakes are applied. When brakes are then released, it takes some time for the reservoirs to be recharged. The lap position, however, functions only if the auxiliary reservoirs are full. So, to stay in full control over non-self-lapping brakes it is recommended to not release when knowing that moments later braking may be needed again. Calculated, infrequent moves are advised instead.
 </div>
 <div lang="en" dir="ltr" class="mw-content-ltr">
-Auxiliary reservoirs are being drained when braking. When the brakes are released, it takes some time for auxiliary reservoirs to fill up again. The lap position, however, functions only if the auxiliary reservoirs are full. To stay in full control over braking it is recommended to not release non-self-lapping brakes when knowing that moments later braking may be needed again. Calculated, slow moves are preferable when releasing the non-self-lapping brakes.
+==== Monitoring ====
 </div>
 <div lang="en" dir="ltr" class="mw-content-ltr">
-With both brake types, the driver can see exactly how much braking force they are applying by looking at the brake pipe and brake cylinder gauge needles.
+With both control valve types it is crucial to {{pll|Monitoring|monitor the brake pipe and cylinder gauges}} to fully understand the current brake state.
 </div>
-Обидві системи досить прості у використанні, хоча прямодіюча може бути більш інтуїтивно зрозумілою для новачків. Простіше кажучи, в прямодіючій системі положення крану напряму впливає на силу гальмування, тоді як при непрямодіючій системі машиністу треба власноруч встановлювати тиск в циліндрах.
+<div lang="en" dir="ltr" class="mw-content-ltr">
+==== Conflicts ====
+</div>
 <div lang="en" dir="ltr" class="mw-content-ltr">
-In case a train contains motorized vehicles with both self-lapping and non-self-lapping brake valve types, only the self-lapping ones will be functional when operating the brake. For that purpose, vehicles are also equipped with brake cutout valves, which can be used to isolate certain vehicles from the brake system and resolve this conflict.
+In case a train contains multiple motorized vehicles their control valves are in conflict. The conflict can be even more severe if there are mixed self-lapping and non-self-lapping valves in the train. To ensure safe operation it is necessary to {{pll|Brake Cutout|cutout}} all excess control valves, other than the one intended to be used.
 </div>
-{{See also|Air Brake System Overview|Brake Cutout|Monitoring|Train Brake|Independent Brake|Brake Shoes}}
 [[Category:Air Brake System|2]]