Lapping/zh-hans: Difference between revisions

Latest revision as of 17:03, 17 March 2025

根据机车车型的不同，有两种控制制动管压力的方法：自动保持和较旧的手动保持。

Self-Lapping

在自动保持系统上，制动管压力会自动调节。司机可以直接将列车制动手柄设置到任何位置。向“应用”方向设置得越近，制动力越强，反之亦然。该阀门会根据手柄的位置自动处理制动管的排压或加压。

Non-Self-Lapping

The non-self-lapping control valves are older. With them, the control lever manipulates the brake pipe pressure directly, and the process is more hands-on. The lever has a few fixed positions. Two of the positions, called “release” and “service” can be thought of as adding and releasing the brake pipe pressure, respectively. The position in-between them, called “lap”, is used to maintain whatever pressure is in the brake pipe. The furthest position, called “emergency”, releases pressure at the fastest possible rate.

By controlling the brake pipe pressure, you indirectly control the cylinder pressure, and thus, brake application.

Auxiliary reservoirs are partially drained whenever brakes are applied. When brakes are then released, it takes some time for the reservoirs to be recharged. The lap position, however, functions only if the auxiliary reservoirs are full. So, to stay in full control over non-self-lapping brakes it is recommended to not release when knowing that moments later braking may be needed again. Calculated, infrequent moves are advised instead.

Monitoring

With both control valve types it is crucial to monitor the brake pipe and cylinder gauges to fully understand the current brake state.

Conflicts

In case a train contains multiple motorized vehicles their control valves are in conflict. The conflict can be even more severe if there are mixed self-lapping and non-self-lapping valves in the train. To ensure safe operation it is necessary to cutout all excess control valves, other than the one intended to be used.

@@ Line 1: / Line 1: @@
 <languages />
+<div class="mw-translate-fuzzy">
 根据机车车型的不同，有两种控制制动管压力的方法：自动保持和较旧的手动保持。
+</div>
+<div lang="en" dir="ltr" class="mw-content-ltr">
+==== Self-Lapping ====
+</div>
+<div class="mw-translate-fuzzy">
 在自动保持系统上，制动管压力会自动调节。司机可以直接将列车制动手柄设置到任何位置。向“应用”方向设置得越近，制动力越强，反之亦然。该阀门会根据手柄的位置自动处理制动管的排压或加压。
+</div>
+<div lang="en" dir="ltr" class="mw-content-ltr">
+==== Non-Self-Lapping ====
+</div>
+<div lang="en" dir="ltr" class="mw-content-ltr">
+The non-self-lapping control valves are older. With them, the control lever manipulates the brake pipe pressure directly, and the process is more hands-on. The lever has a few fixed positions. Two of the positions, called “release” and “service” can be thought of as adding and releasing the brake pipe pressure, respectively. The position in-between them, called “lap”, is used to maintain whatever pressure is in the brake pipe. The furthest position, called “emergency”, releases pressure at the fastest possible rate.
+</div>
+<div lang="en" dir="ltr" class="mw-content-ltr">
+By controlling the brake pipe pressure, you indirectly control the cylinder pressure, and thus, brake application.
+</div>
 <div lang="en" dir="ltr" class="mw-content-ltr">
-On non-self-lapping systems, the process is more hands-on. The lever has a few fixed positions. Two of the positions, called “release” and “service” can be thought of as adding and releasing the brake pipe pressure, respectively. The position in between them, called “lap”, is used to maintain whatever pressure is in the brake pipe. The furthest position, called “emergency”, will release pressure at the fastest possible rate.
+Auxiliary reservoirs are partially drained whenever brakes are applied. When brakes are then released, it takes some time for the reservoirs to be recharged. The lap position, however, functions only if the auxiliary reservoirs are full. So, to stay in full control over non-self-lapping brakes it is recommended to not release when knowing that moments later braking may be needed again. Calculated, infrequent moves are advised instead.
 </div>
 <div lang="en" dir="ltr" class="mw-content-ltr">
-Auxiliary reservoirs are being drained when braking. When the brakes are released, it takes some time for auxiliary reservoirs to fill up again. The lap position, however, functions only if the auxiliary reservoirs are full. To stay in full control over braking it is recommended to not release non-self-lapping brakes when knowing that moments later braking may be needed again. Calculated, slow moves are preferable when releasing the non-self-lapping brakes.
+==== Monitoring ====
 </div>
 <div lang="en" dir="ltr" class="mw-content-ltr">
-With both brake types, the driver can see exactly how much braking force they are applying by looking at the brake pipe and brake cylinder gauge needles.
+With both control valve types it is crucial to {{pll|Monitoring|monitor the brake pipe and cylinder gauges}} to fully understand the current brake state.
 </div>
-两种系统都相当易于使用，尽管自动研磨对初学者来说可能更直观。简单来说，对于自研，控制装置设置所需的制动力，将其留给自动阀来完成工作，而对于非自研，控制装置直接设置制动力。
+<div lang="en" dir="ltr" class="mw-content-ltr">
+==== Conflicts ====
+</div>
 <div lang="en" dir="ltr" class="mw-content-ltr">
-In case a train contains motorized vehicles with both self-lapping and non-self-lapping brake valve types, only the self-lapping ones will be functional when operating the brake. For that purpose, vehicles are also equipped with brake cutout valves, which can be used to isolate certain vehicles from the brake system and resolve this conflict.
+In case a train contains multiple motorized vehicles their control valves are in conflict. The conflict can be even more severe if there are mixed self-lapping and non-self-lapping valves in the train. To ensure safe operation it is necessary to {{pll|Brake Cutout|cutout}} all excess control valves, other than the one intended to be used.
 </div>
-{{See also|Air Brake System Overview|Brake Cutout|Monitoring|Train Brake|Independent Brake|Brake Shoes}}
 [[Category:Air Brake System|2]]